How to Make a Cortado at Home
Pour equal weights of espresso and lightly steamed milk, then adjust by a few grams to keep the coffee flavor clear.
Around 9 bar is a common brewing-pressure reference for conventional espresso. It helps drive water through finely ground coffee, but hitting 9 bar does not guarantee a balanced shot. A machine advertised with a 15- or 20-bar pump is not automatically better: pump capability and pressure during brewing are different things.
For most home espresso owners, the useful starting point is the machine’s intended brewing setup. Keep it steady while you establish a suitable dose (dry coffee used), grind and output (espresso collected). If the shot tastes good and repeats reliably, there is no need to change pressure simply to match advice online. The dialing-in method explains how to establish that measured recipe.
A manometer, or pressure gauge, is a clue to what the system is doing. Read it alongside how quickly espresso collects and how the finished drink tastes.
These checks apply to a conventional machine with a non-pressurized basket: an ordinary perforated basket without an extra pressure-building outlet. Read the whole row before making a change; a needle position alone cannot identify the cause.
| What you notice | A useful first check |
|---|---|
| Low pressure and unusually fast, weak espresso | Confirm the basket, suitable dose and even preparation. If those are consistent, try one small finer-grind step and compare the same output weight before assuming the pump is faulty. |
| High pressure but very little espresso | Stop the struggling shot and follow the manual before removing the portafilter (the handled basket holder). Check basket fill and cleanliness. If those are suitable, try one small coarser-grind step. More pressure is not the first correction. |
| A familiar pressure reading, but unpleasant flavor | Compare the measured recipe, preparation, machine readiness and coffee. Reaching the usual number does not certify the drink. |
| Pressure falls as the shot speeds up | Check whether this matches the machine’s profile. If unexpected, compare preparation and output across repeated shots before choosing a cause. |
| A sudden change across normally repeatable recipes | Check water supply and the manual’s cleaning and troubleshooting guidance. Persistent abnormal behavior may need manufacturer support. |
| Repeatable espresso that tastes balanced | Keep the recipe. A reading that differs from someone else’s machine is not, by itself, a reason to intervene. |
With a pressurized basket or an automatic machine, use the model’s instructions: its outlet or brewing system changes how these clues should be interpreted.

Bar is a unit of pressure. Conventional machine gauges usually show pressure above the surrounding air pressure. A 9-bar gauge reading is therefore a pressure difference, rather than a measurement of how much water passed through the coffee.
The compact bed of grounds in the filter basket is called the puck. It resists water flow. Brewing pressure provides the driving force to move water through that resistance.
Pressure and flow are different measurements. Pressure describes the driving force per unit area; flow describes how much water moves in a given time. High pressure can exist while a very restricted puck lets almost no drink reach the glass.
Around 9 bar is an established operating reference used by many conventional pump machines. For example, La Marzocco describes its home machines as factory-set to brew at 9 bar. This makes it a useful starting reference for compatible equipment, rather than a universal instruction for every design.
The 9-bar reference belongs to a complete brewing setup: fine grounds, a compact coffee bed and a relatively small drink collected over a short period. It is an established working point, not a scientifically fixed best pressure for every coffee. Keeping an appropriate setup steady gives you one fewer variable while you work on the recipe.
Increasing pressure changes brewing conditions, but does not guarantee more desirable extraction. The resulting drink also depends on the coffee bed, water delivery, temperature and amount collected. Pressure cannot compensate for every problem elsewhere in that system.
A higher advertised pump rating is not a quality score. A pump’s rated capability is different from the pressure the machine develops during a particular shot. Valves, controls, water flow and resistance all affect operation.
Breville provides a useful model-specific example: its Barista Express product information describes a 15-bar pump and 9-bar extraction. Those two numbers refer to different aspects of the same machine.
Check what a specification actually describes. A headline might state a maximum pump capability, while the manual explains the intended brewing behavior. Neither tells you that every part of the puck remains at that pressure throughout a shot.
For an existing machine, focus first on whether it delivers repeatable recipes with the coffee and basket you use. Shopping for a bigger number, or trying to make the gauge reach the advertised maximum, is not a useful route to better flavor.
Start by identifying the gauge. Some machines display brew pressure, some show steam-boiler pressure, and some have both. A steam reading should not be judged against a 9-bar brewing reference.
If you are unsure which controls your machine actually provides, check the guide to identifying espresso machine controls.
Some gauges show a colored espresso range rather than numbered bar markings. Use the manual to interpret that range; the needle’s position alone does not establish an exact pressure.
Then check where the machine measures pressure. A reading in the pump circuit and one near the brewing group describe different locations. Gauge accuracy and the machine’s water path also matter, so two machines’ numbers are not automatically interchangeable.
Observe the main brewing phase, after any initial wetting stage. Note whether the reading is steady or changing, how the espresso collects, and the final output. A brief peak is not the same as sustained brewing pressure.

Pressure seen while the machine is idle can have a different explanation. Some designs show a rise as trapped water heats and expands. Interpret that behavior through the manual rather than treating every high idle reading as excessive pressure through coffee.
A test with a blind basket, which blocks the outlet, also differs from brewing through a coffee puck. Perform only the tests prescribed for your model. A blocked-outlet reading is not proof of the pressure or flow during an ordinary shot.
Finally, a gauge cannot reveal whether all the grounds received water evenly. A familiar reading can coexist with channeling, where water takes easier paths through the bed. Nor does pressure tell you how concentrated the drink is or how much coffee material was dissolved.
Use the gauge to add context to a repeatable recipe. Avoid grinding finer solely to push a needle into a preferred zone if the resulting drink barely flows or tastes worse.
If you changed basket types, compare how basket restrictions affect flow before attributing a different reading to the pump.
Pre-infusion is an initial wetting stage before the main brewing phase. Depending on the machine, it may use lower pressure, restricted water delivery or a pause. A lower reading during that stage does not necessarily indicate a fault.
Pressure profiling deliberately changes pressure through the shot. Flow-control systems change water delivery, which also interacts with pressure and puck resistance. These controls are related, but their settings are not interchangeable.
If your machine follows a programmed profile, compare the reading with that profile. Do not expect a constant 9 bar from a recipe designed to rise, hold and decline.
On a manual lever, your action helps create the brewing pressure. Some lever designs and recipes use a declining pressure pattern. Follow the specific machine’s guidance before comparing its needle movement with a pump machine.
Flair, for example, gives a 6–9 bar brewing range for certain models. That is useful evidence that espresso does not require an unchanging 9-bar reading. It is not a replacement setting for every other machine.
A non-pressurized basket has a perforated base, with the coffee bed providing much of the brewing resistance. A pressurized or dual-wall basket adds restriction at its outlet.
That added restriction means pressure and the visible stream reflect more than the grounds alone. Use the recommended basket, coffee preparation and dose for your equipment; do not transfer grind instructions between basket types without checking.
Fully automatic and capsule machines manage brewing differently again. Use their intended controls and troubleshooting routines rather than trying to impose a traditional portafilter recipe or a particular gauge number.
Pressure is worth exploring when your machine provides an intended user control, your basic recipe repeats reliably, and you can describe what you want to improve. Many home owners can make useful improvements without adjusting it.
If your machine has no intended pressure control, leave its pressure setup alone. Hold a suitable dose steady, use small grind changes to address flow, and compare a measured output and the finished flavor. If the machine suddenly stops behaving normally, follow its troubleshooting guidance before changing the recipe.
Opening a machine to alter a pump or over-pressure valve is a service task, separate from using a documented brewing control. Consult the manufacturer or a qualified technician when the intended operation is unclear.

On a machine with a documented brew-pressure control, keep the same dose, grind and drink weight for both shots. Record the gauge reading during flow, the elapsed time and the taste. Check the location and purpose of your gauge in the Espresso Machine Guide before comparing numbers across machines.
Hypothetical example: suppose your adjustable machine supports both 9- and 8-bar settings. You use an 18 g dose and collect 36 g of espresso, then compare the second setting with the same preparation. These weights are illustrative, not a dose recommendation for every basket.
A change in time at the same output tells you that the average beverage flow changed. Taste both shots and repeat the comparison before keeping the new setting.
Not automatically. Some equipment and recipes intentionally brew below 9 bar. An unexpected low reading combined with fast, weak output deserves investigation; an intentional lower-pressure recipe should be assessed on its own terms.
No. Crema also depends on coffee characteristics, gas and brewing conditions. Its thickness cannot establish whether the espresso tastes balanced or the puck extracted evenly.
No. Grind can be one cause in a conventional basket, but dose, preparation, basket design, the brewing stage and machine operation also matter. Check the whole result before choosing an adjustment.
Yes. A gauge adds information, but a suitable measured recipe and repeatable preparation remain useful without one. Follow the machine’s intended setup, track dose and output where possible, and let careful tasting guide the next change.
Pour equal weights of espresso and lightly steamed milk, then adjust by a few grams to keep the coffee flavor clear.
Use your usual espresso dose, stop at a shorter yield, and taste both shots to find the texture and flavor you prefer.
Mark an espresso with a small spoonful of milk foam. Learn how to get the texture right and adjust the milk to suit the shot.
Leave a comment