How to Make a Cortado at Home
Pour equal weights of espresso and lightly steamed milk, then adjust by a few grams to keep the coffee flavor clear.
Espresso grinder retention is the ground coffee that stays inside the grinder instead of reaching your dosing cup or basket. Some of those grounds may come out with a later dose, carrying an earlier coffee or grind setting into your next shot.
Follow your exact model’s instructions for loading, adjusting and clearing the grinder.
Matching input and output weights do not prove that all the grounds are fresh from that dose. The example below explains how earlier coffee can enter a dose with a matching weight.
Coffee can remain around the burrs, inside the grinding chamber or along the exit chute. The burrs are the grinding surfaces; the chute carries the grounds toward your container. Static and accumulated residue can also make grounds cling to surfaces.
Three terms are often discussed as though they mean the same thing:
| Term | What it describes | What to remember |
|---|---|---|
| Total retention | All the ground coffee remaining inside the grinder at a particular point. | Measuring it requires an appropriate collection method; a routine dose check does not reveal it. |
| Exchanged grounds | Earlier grounds that leave with a later dose while newer grounds remain behind. | The dose can contain exchanged coffee even when input and output weights match. |
| Input–output difference | The difference between the beans loaded and the grounds collected. | Spills, unground beans, clinging grounds and weighing errors can affect the result. |
Manufacturers and reviewers may use different test methods. A low retention number needs context: was it measured immediately after cleaning, over repeated doses, or after using a clearing accessory?
Imagine a simplified case with no spills: you add 18.0 g of beans and collect 18.0 g of grounds. Of that output, 17.6 g comes from the new beans and 0.4 g comes from an earlier dose. Meanwhile, 0.4 g of the newly ground coffee stays inside.
The scale still shows matching weights. These numbers illustrate exchange; they are not measurements of a particular grinder.
How a matching 18 g output can contain earlier coffee
Three parts of preparation are worth checking: the basket dose, the response to an adjustment and the coffee carried into the next shot.
If you load a known amount of beans but collect less, the basket may receive less coffee than your recipe calls for. Grounds left in the dosing cup during transfer create a separate loss.
Weigh the actual basket dose when investigating variation. Tare the empty, dry portafilter with its basket in place, then add the grounds and reweigh. Keep the handle clear of the counter so it does not support part of the weight.
For a hopper grinder, the beans already inside prevent a simple per-dose input comparison. You can still weigh the grounds delivered to the basket and check whether that amount repeats.
Grounds left from the previous setting can mix with grounds produced at the new one. The first shot after an adjustment may therefore give incomplete feedback about the change.
That can lead to unnecessary corrections: you move the dial again because the shot hardly changed, then a later shot behaves very differently. Before adjusting a second time, clear the grinding path as directed and check the dose.
After switching beans, some grounds from the first coffee may remain in the grinding path. After a period of disuse, retained grounds may also have aged more than the beans you are about to grind.
How much this affects the drink depends on the amount exchanged, time and conditions. An unusual first shot is a reason to investigate, rather than proof that retention is the cause.
Weigh a few of your normal preparations with a scale that can resolve the differences you want to track. Keep the collection routine the same so the weights are comparable.
For a repeatable baseline, use the espresso grinder guide. If your grinder is integrated, check the supported controls in the guide to your machine setup before changing the dose routine.

If your manufacturer supports weighing and grinding one portion at a time:
This checks delivery in your routine. It does not measure all the coffee held inside or the exact amount exchanged.
For example, loading 18.0 g and collecting 17.7 g gives a 0.3 g difference. If some coffee spilled, that difference is not all internal retention. If the next output exceeds its input, previously retained grounds may have been released; check the scale and collection conditions as well.
Keep the hopper supplied as the manufacturer recommends and weigh what each normal dispensing cycle delivers. Record the grinding time or selected dose alongside the result.
If the amount varies, check loading, cleanliness and dose controls before changing the grind. After a grind adjustment, recheck the delivered weight: the same timed cycle does not establish the same basket dose.
A purge moves coffee through the grinding path before you collect the dose you intend to brew. It is most relevant when earlier grounds could interfere with your next comparison.
If you switch coffees by weighing one dose at a time, compare the single-dose workflow to see which steps you can repeat.

| Situation | A useful next step |
|---|---|
| You made a substantial grind adjustment. | Clear the previous grounds as directed, then compare shots at the same basket dose and espresso weight. |
| You switched coffees or brew methods. | Clear the previous coffee as directed and evaluate the first dose against the new coffee’s recipe. |
| The grinder has been idle and the first drink repeatedly disappoints. | Check machine readiness and dose, then compare a routine with and without an appropriate purge. |
| Consecutive doses already repeat and taste good. | Keep the routine; investigate a specific change before adding more waste. |
Baratza’s guidance on switching grind settings explains why grounds from an earlier setting can affect the next dose. Its operating advice applies to its grinders; another model may require a different procedure.
Begin with the purge quantity or clearing sequence specified for your model. Then check how that routine works with your coffee:
Keep the routine when the dose repeats, adjustments give understandable feedback and the espresso tastes good. Compare similar transitions over normal use before adding a larger purge.
If the manual gives no quantity, record what your current approved clearing routine uses. Ask the manufacturer for guidance if transitions remain unclear. An unchanged shot alone does not establish that more purging is needed; dose, preparation and machine readiness also deserve a check.
Aim for a dependable dose and a manageable transition between coffees or settings. Begin with the tools and maintenance steps specified for your grinder.
Place the dosing cup correctly and use any supplied knocker, bellows or clearing tool as directed. Bellows push air through the grinding path; their presence does not establish how much coffee remains inside.
Use the same sequence before weighing each dose so the comparison remains useful. Avoid forceful tapping or inserting improvised tools into the chute.
Coffee buildup can interfere with the grounds path. Cleaning requirements depend on the design: Fellow’s Opus 1 maintenance guidance, for example, includes cleaning the exit chute and anti-static pins.
Switch off and unplug an electric grinder before removing components or brushing inside. Follow its access, reassembly and approved cleaning-product instructions.

Purging and cleaning serve different purposes. Passing new coffee through may displace earlier grounds, while compacted residue and oils can still require maintenance. Increasing a purge is a poor substitute for checking a restricted outlet.
Check your exact model’s instructions before adding water to beans to reduce static. Some manufacturers advise against it. When permitted, follow the specified method and amount.
Look for a basket dose you can repeat, understandable responses to adjustments and espresso you enjoy. A small input–output difference is useful information; it is not a complete quality score.
If the dose now repeats but the shot still needs a grind change, use the finer-or-coarser chart to choose the next comparison.
If the first shot repeatedly differs from the next, note the pattern before changing anything. Check machine warm-up, basket dose, target output and preparation. Compare first shots on similar mornings, using the same warm-up and recording the idle period. Change one supported clearing step while keeping those conditions steady. A repeated improvement supports keeping the step, but does not identify the exact mass exchanged.
Stop adding steps when the routine delivers repeatable results you like. Retention deserves attention when it creates a practical problem, not simply because a few grounds are visible.
Treat “zero retention” as a claim to examine alongside its test method. Very low input–output differences do not prove that every surface is empty or that no earlier grounds enter the next dose. Normal cleaning requirements still apply.
There is no single normal amount for every grinder and test method. Check whether a figure describes total retention or an input–output difference before comparing numbers. For your own routine, look for a repeatable basket dose, understandable responses to adjustments and a manageable amount of purged coffee. Investigate a sudden change from your grinder’s usual delivery.
Check spills, transfer losses and the clearing routine first. Adding a fixed allowance can miss changes from one preparation to the next. Base your recipe on the grounds reaching the basket, and follow the manufacturer’s dosing guidance.
A sudden large shortfall or failure to dispense needs the model’s troubleshooting procedure. Stop and investigate rather than adding beans or repeatedly running a stalled motor. Contact the manufacturer if the approved clearing steps do not restore normal operation.
Pour equal weights of espresso and lightly steamed milk, then adjust by a few grams to keep the coffee flavor clear.
Use your usual espresso dose, stop at a shorter yield, and taste both shots to find the texture and flavor you prefer.
Mark an espresso with a small spoonful of milk foam. Learn how to get the texture right and adjust the milk to suit the shot.
Leave a comment